The Meade LX200 GPS telescopes are capable of being controlled by means of the Meade Hand Pad/Controller, and/or controlled by a personal computer. While connected to a computer, the Hand Controller may still be used if needed without any interruption to the computer. TPoint or equivalent programs can also be implemented to help improve the pointing and go-to accuracy of the Meade LX200 GPS.
Control and Connecting a Meade LX200 GPS to PC Computer
On the fork mount base of the LX200, you will find the face plate where all the cables connect. This is the access panel of the telescope. Here, the power supply, the hand controller, CCD auto-guider cable, and computer serial port can be connected. The computer will connect to the telescope by means of the serial port and these cables can be purchased or easily made.
For longer cables, a high quality phone line may be used in place of the standard cable that is included with the telescope hand controller when purchased from the manufacturer. Once you have the serial cable connected to the computer serial port and the telescope, verify the connection by using the “connection” option in TheSky6.
For more information on the LX200, see "Astronomy How To: The Meade LX200 GPS Schmitt-Cassegrain Telescope"
Connecting the SBIG CCD Imager to the PC and Meade LX200 GPS Telescope
Attach the CCD Imager to the telescope by using the nosepiece that was designed for the camera. If you decide to use the Meade micro-focuser, the nosepiece of the camera will attach directly to the focuser and the two focuser set screws can be secured to the camera (double check these to prevent the camera from slipping).
If a focal reducer is used, it will attach between the CCD imager and the focuser. If the Meade Diagonal is used, the focal reducer will be mounted between the CCD and the diagonal. There are many types of focal reducers as well as a variation of focal reducer positions that will allow different focal lengths.
A word of caution: If the Meade micro-focuser is used with the SBIG CCD camera, it WILL come in contact with the fork mount when slewing to certain positions. The maximum slew limits will need to be set when the micro-focuser is used, to prevent damage.
Connecting the SBIG CCD Imager to the Computer
This is a fairly easy step. Most CCD imagers now use USB for computer connection. USB is much faster than the older parallel-port versions and more reliable. But, many parallel-port version CCD imagers are still in use today. If your CCD is a USB version, simply plug it into any USB port on your computer - if it’s a parallel version, connect it to the 25 pin parallel port on your computer. There are also adapter kits that will covert your parallel port CCD imager to USB, but regardless of the conversion, the imager will still work and upload the images to the PC at parallel speed. The other option is to return your CCD imager to SBIG for a rather expensive upgrade to USB.
Configuring CCDSoft and the SBIG CCD Imager
Run CCDSoft and open the “camera” tab. Here you will see the configuration window for the camera control. Select the “setup” tab and then choose your particular camera in the “camera” drop-down menu. Once selected, click the “settings” button and make any adjustments needed for your camera.
Also under the “setup” tab, you will need to setup a filter wheel (if used), a focuser, and any other necessary settings can be made here. Once the CCD is connected to your computer and the power cord is plugged in, turn on the computer, start CCDSoft, open the camera control window and click on “connect”. The software should then show the camera as “connected” under Status and you should now be able to see the temperature setting.
Open the temperature setting and verify that the “desired temperature” is set close to the “recommended temperature”. For example: If the “recommended temperature” is -5° C. and the “desired temperature” is set to -30° C., it’s likely the camera will never reach the “desired temperature” and the camera will overwork itself while attempting to reach the desired temperature.
If your camera fails to connect and you get an error, you can go to the SBIG Web site for a solution to the particular error (normally a software generated code). Make any further set-up changes needed and reattempt to connect the CCD imager.
Configuring TheSky6 Professional for the Meade LX200 GPS
Run TheSky6 Professional from your computer and select “Telescope” > Telescope Set-up > Name: drop down menu > Meade LX200GPS. Once this is selected, choose the correct COM port that will allow the computer to connect to the LX200 GPS (refer to TheSky6 help menu for further assistance and setup options.) Finally, from the main window in TheSky6, select Telescope > Link > Establish. It should now show a connection to the telescope. If not, double check your settings and reattempt.
Now, run CCDSoft and connect it to your camera. At this point, you should have a connection with your telescope and camera.
Synchronizing the CCD Imager for Autoguiding the Meade LX200 GPS
Once you have read the documentation on CCDSoft and have your camera set-up properly, it needs to be synchronized to the telescope. CCDSoft has an automated synchronization process that simplifies this step. In the “camera control” window, select the auto-guide tab and then select synchronize. The software will take a series of images and make fine adjustments in your scopes positions. It does this to determine any slight error and the motion of the scope drive. Once it completes this process, you will be able to use the auto-guider as well as auto-center objects in your field of view.
Synchronizing the Meade LX200 Telescope with TheSky6 Professional
The CCD imager must be synchronized before performing this step. After connecting TheSky6 to the Meade LX200, look at the planetarium screen of TheSky6 and verify the telescope crosshairs are visible in the star chart. Manually slew the telescope to a known brighter star and adjust the telescope until the star is centered in the field of view. In CCDSoft, select the Autoguide tab in the Camera Control window and click the Imager radio button (below it is the guider radio button). Take a short exposure to verify that the known star is within the field of view.
If any focusing is needed, it should be done now, but perfect focus is not needed at this point – just get it close. For now, use the LX200 GPS hand controller for focusing. In CCDSoft, Right click on the known star and a menu will appear that has the options “center brightest object” or “center pointer position”. Select “center cursor position”. CCDSoft will then attempt to center the position of the cursor. Once it has completed, take another short exposure and check the star position. It should now be near the center of the field of view, but sometimes this process takes 2 or 3 tries before obtaining perfect center.
Once the star is centered in the field of view, click on the star in TheSky6 and a window will pop-up. Within this menu, you will see the telescope “sync” option. Click the “sync” button and TheSky6 will ask to confirm the synchronization. Click OK and now the computer and telescope will be synchronized on the star. This allows TheSky6 to have an understanding of exactly where the telescope is pointing. If the telescope has been properly aligned, it should be capable of slewing to nearly any celestial object in the sky.
Related article: " Astronomy - Hunting Comets with a Meade LX200 GPS Telescope and DSLR"
On-line References:
Santa Barbara Instruments Group - SBIG CCD Imagers
Meade Instruments - Telescopes, Solar Telescopes, Telescope Accessories
Software Bisque - TheSky6 Professional
Software Bisque - CCDSoft
Steve Farmer - Steve Farmer Jr. is an individual of many interests and hobbies. When not spending time with his wife and four children, he is an employee ...
Join the Conversation